Forum

Pages: 1 2

Hi ! I'm French and new to Raspberry Bi+.
I want to build a media center and so i installed XBian on it. It was the RC1, my wifi usb key was working with it but i did not manage to connect my network (even if it was "seen"). I set up today RC3 in order to fix this. But now my key isn't working anymore.

Do you have any solution ?

Thanks a lot for your help !

What do you mean by key? Wifi password?

No, the USB connector was detected in RC1 (but i didn't manage to enter the key) but not in RC3

Hi Thib,

to help your helpers helping fastly, you should always provide as much information as possible within your first post.
(For the next time: http://forum.xbian.org/announcement-9.html)

For this specific problem, you should at least provide more info about your wifi stick.
Maybe you should just post your output of a few commands:

Terminal

xbian@xbian ~ $ lsusb

Terminal

xbian@xbian ~ $ lsmod

Terminal

xbian@xbian ~ $ ifconfig -a

Terminal

xbian@xbian ~ $ dmesg

Probably I may can't help you, but I'm sure some of these outputs can speed things up so that others can do.
Otherwise it's like ping-pong. Wink

Hi, sorry for this and thanks for your help Smile

Here is my outputs for lsusb :

Code:

Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp.

Bus 001 Device 004: ID 046d:c315 Logitech, Inc. Classic New Touch Keyboard

Bus 001 Device 006: ID 0bda:8179 Realtek Semiconductor Corp.

The 6th one corresponds to my Wifi usb stick.

For lsmod :

Code:

Module                  Size  Used by

nfsd                  200831  2

r8188eu               626945  0

frandom                 3555  0

vchiq                 192710  0

For lsconfig -a

Code:

dummy0    Link encap:Ethernet  HWaddr EE:35:B2:03:E6:6B

          BROADCAST NOARP  MTU:1500  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0

          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr B8:27:EB:94:07:CA

          inet addr:192.168.137.113  Bcast:192.168.137.255  Mask:255.255.255.0

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:1113 errors:0 dropped:0 overruns:0 frame:0

          TX packets:920 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000

          RX bytes:447498 (437.0 KiB)  TX bytes:189729 (185.2 KiB)

lo        Link encap:Local Loopback

          inet addr:127.0.0.1  Mask:255.0.0.0

          UP LOOPBACK RUNNING  MTU:65536  Metric:1

          RX packets:72 errors:0 dropped:0 overruns:0 frame:0

          TX packets:72 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0

          RX bytes:4864 (4.7 KiB)  TX bytes:4864 (4.7 KiB)

wlan0     Link encap:Ethernet  HWaddr E8:DE:27:13:B4:6A

          BROADCAST MULTICAST  MTU:1500  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000

          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

And last, but not least, the outputs for dmesg, that's one is pretty long !

Code:

[    0.000000] Booting Linux on physical CPU 0x0

[    0.000000] Linux version 3.15.8+ (mk@debian) (gcc version 4.4.5 (Debian 4.4.5-8) ) #4 Wed Sep 24 14:30:32 CEST 2014

[    0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d

[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache

[    0.000000] Machine: BCM2708

[    0.000000] cma: CMA: reserved 16 MiB at 16000000

[    0.000000] Memory policy: Data cache writeback

[    0.000000] On node 0 totalpages: 94208

[    0.000000] free_area_init_node: node 0, pgdat c0686b88, node_mem_map d5d10000

[    0.000000]   Normal zone: 736 pages used for memmap

[    0.000000]   Normal zone: 0 pages reserved

[    0.000000]   Normal zone: 94208 pages, LIFO batch:31

[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768

[    0.000000] pcpu-alloc: [0] 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 93472

[    0.000000] Kernel command line: selinux=0  dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1080 bcm2708.boardrev=0x10 bcm2708.serial=0x549407ca smsc95xx.macaddr=B8:27:EB:94:07:CA bcm2708.disk_led_gpio=47 bcm2708.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000  telnet zswap.enabled=1 zswap.compressor=lz4 sdhci-bcm2708.sync_after_dma=0 dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p2 rootflags=subvol=root/@,thread_pool=2,autodefrag,compress=lz4,commit=120 rootfstype=btrfs rootwait smsc95xx.turbo_mode=N elevator=cfq logo.nologo quiet noswap loglevel=0 mod_scsi.scan=sync partswap startevent=mountall splash nohdparm --startup-event mountall

[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[    0.000000] Memory: 345260K/376832K available (4952K kernel code, 232K rwdata, 1352K rodata, 131K init, 251K bss, 31572K reserved)

[    0.000000] Virtual kernel memory layout:

[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)

[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)

[    0.000000]     vmalloc : 0xd7800000 - 0xff000000   ( 632 MB)

[    0.000000]     lowmem  : 0xc0000000 - 0xd7000000   ( 368 MB)

[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)

[    0.000000]       .text : 0xc0008000 - 0xc0630384   (6305 kB)

[    0.000000]       .init : 0xc0631000 - 0xc0651efc   ( 132 kB)

[    0.000000]       .data : 0xc0652000 - 0xc068c2a8   ( 233 kB)

[    0.000000]        .bss : 0xc068c2a8 - 0xc06cb250   ( 252 kB)

[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[    0.000000] NR_IRQS:394

[    0.000017] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483648000ns

[    0.000048] Switching to timer-based delay loop

[    0.000272] Console: colour dummy device 80x30

[    0.000426] console [tty1] enabled

[    0.000443] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=1000)

[    0.000460] pid_max: default: 32768 minimum: 301

[    0.000583] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)

[    0.000602] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)

[    0.001307] Initializing cgroup subsys memory

[    0.001378] CPU: Testing write buffer coherency: ok

[    0.001736] Setting up static identity map for 0x4bd170 - 0x4bd1a8

[    0.004204] devtmpfs: initialized

[    0.019042] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5

[    0.019371] xor: measuring software checksum speed

[    0.029479]    arm4regs  :  1164.000 MB/sec

[    0.039532]    8regs     :   592.000 MB/sec

[    0.049578]    32regs    :   740.000 MB/sec

[    0.049591] xor: using function: arm4regs (1164.000 MB/sec)

[    0.051566] NET: Registered protocol family 16

[    0.056934] DMA: preallocated 4096 KiB pool for atomic coherent allocations

[    0.057470] cpuidle: using governor menu

[    0.058165] bcm2708.uart_clock = 3000000

[    0.059922] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.

[    0.059938] hw-breakpoint: maximum watchpoint size is 4 bytes.

[    0.059950] mailbox: Broadcom VideoCore Mailbox driver

[    0.060020] bcm2708_vcio: mailbox at f200b880

[    0.060098] bcm_power: Broadcom power driver

[    0.060113] bcm_power_open() -> 0

[    0.060121] bcm_power_request(0, 8)

[    0.560777] bcm_mailbox_read -> 00000080, 0

[    0.560791] bcm_power_request -> 0

[    0.560890] Serial: AMBA PL011 UART driver

[    0.561008] dev:f1: ttyAMA0 at MMIO 0x20201000 (irq = 83, base_baud = 0) is a PL011 rev3

[    0.604572] raid6: int32x1     58 MB/s

[    0.621620] raid6: int32x2     89 MB/s

[    0.638955] raid6: int32x4     85 MB/s

[    0.655726] raid6: int32x8     74 MB/s

[    0.655740] raid6: using algorithm int32x2 (89 MB/s)

[    0.655749] raid6: using intx1 recovery algorithm

[    0.656385] SCSI subsystem initialized

[    0.656646] usbcore: registered new interface driver usbfs

[    0.656738] usbcore: registered new interface driver hub

[    0.656949] usbcore: registered new device driver usb

[    0.658743] Switched to clocksource stc

[    0.669576] NET: Registered protocol family 2

[    0.670522] TCP established hash table entries: 4096 (order: 2, 16384 bytes)

[    0.670619] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)

[    0.670682] TCP: Hash tables configured (established 4096 bind 4096)

[    0.670807] TCP: reno registered

[    0.670831] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.670857] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.671085] NET: Registered protocol family 1

[    0.671480] RPC: Registered named UNIX socket transport module.

[    0.671500] RPC: Registered udp transport module.

[    0.671508] RPC: Registered tcp transport module.

[    0.671515] RPC: Registered tcp NFSv4.1 backchannel transport module.

[    0.671899] Unpacking initramfs...

[    1.218095] Freeing initrd memory: 4800K (c1000000 - c14b0000)

[    1.228995] bcm2708_dma: DMA manager at f2007000

[    1.229118] bcm2708_gpio: bcm2708_gpio_probe c065bba0

[    1.229461] vc-mem: phys_addr:0x00000000 mem_base=0x1ec00000 mem_size:0x20000000(512 MiB)

[    1.230364] futex hash table entries: 256 (order: -1, 3072 bytes)

[    1.238286] zbud: loaded

[    1.238925] VFS: Disk quotas dquot_6.5.2

[    1.239173] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[    1.241680] NFS: Registering the id_resolver key type

[    1.241828] Key type id_resolver registered

[    1.241844] Key type id_legacy registered

[    1.241871] nfs4filelayout_init: NFSv4 File Layout Driver Registering...

[    1.242654] msgmni has been set to 715

[    1.244408] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)

[    1.244430] io scheduler noop registered

[    1.244439] io scheduler deadline registered

[    1.244698] io scheduler cfq registered (default)

[    1.245927] BCM2708FB: allocated DMA memory 56400000

[    1.245984] BCM2708FB: allocated DMA channel 0 @ f2007000

[    1.267266] Console: switching to colour frame buffer device 240x67

[    1.282866] uart-pl011 dev:f1: no DMA platform data

[    1.284358] usbcore: registered new interface driver smsc95xx

[    1.284418] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)

[    1.484574] Core Release: 2.80a

[    1.484595] Setting default values for core params

[    1.484636] Finished setting default values for core params

[    1.684799] Using Buffer DMA mode

[    1.684824] Periodic Transfer Interrupt Enhancement - disabled

[    1.684833] Multiprocessor Interrupt Enhancement - disabled

[    1.684843] OTG VER PARAM: 0, OTG VER FLAG: 0

[    1.684857] Dedicated Tx FIFOs mode

[    1.685215] WARN::dwc_otg_hcd_init:1042: FIQ DMA bounce buffers: virt = 0xd6414000 dma = 0x56414000 len=9024

[    1.685249] FIQ FSM acceleration enabled for :

[    1.685249] Non-periodic Split Transactions

[    1.685249] Periodic Split Transactions

[    1.685249] High-Speed Isochronous Endpoints

[    1.685271] dwc_otg: Microframe scheduler enabled

[    1.685320] WARN::hcd_init:473: FIQ at 0xc0391644

[    1.685335] WARN::hcd_init:474: FIQ ASM at 0xc03919c0 length 36

[    1.685359] WARN::hcd_init:500: MPHI regs_base at 0xd7810000

[    1.685383] dwc_otg bcm2708_usb: DWC OTG Controller

[    1.685430] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1

[    1.685476] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000

[    1.685510] Init: Port Power? op_state=1

[    1.685519] Init: Power Port (0)

[    1.685794] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[    1.685817] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    1.685831] usb usb1: Product: DWC OTG Controller

[    1.685843] usb usb1: Manufacturer: Linux 3.15.8+ dwc_otg_hcd

[    1.685854] usb usb1: SerialNumber: bcm2708_usb

[    1.686612] hub 1-0:1.0: USB hub found

[    1.686682] hub 1-0:1.0: 1 port detected

[    1.687160] dwc_otg: FIQ enabled

[    1.687177] dwc_otg: NAK holdoff enabled

[    1.687185] dwc_otg: FIQ split-transaction FSM enabled

[    1.687204] Module dwc_common_port init

[    1.687586] usbcore: registered new interface driver usb-storage

[    1.687935] mousedev: PS/2 mouse device common for all mice

[    1.688673] bcm2835-cpufreq: min=700000 max=840000 cur=840000

[    1.688871] bcm2835-cpufreq: switching to governor performance

[    1.688888] bcm2835-cpufreq: switching to governor performance

[    1.688975] sdhci: Secure Digital Host Controller Interface driver

[    1.688987] sdhci: Copyright(c) Pierre Ossman

[    1.689060] sdhci: Enable low-latency mode

[    1.689230] mmc0: no vqmmc regulator found

[    1.689247] mmc0: no vmmc regulator found

[    1.718784] mmc0: SDHCI controller on BCM2708_Arasan [platform] using platform's DMA

[    1.718900] mmc0: BCM2708 SDHC host at 0x20300000 DMA 2 IRQ 77

[    1.718997] ledtrig-cpu: registered to indicate activity on CPUs

[    1.719126] hidraw: raw HID events driver (C) Jiri Kosina

[    1.721515] usbcore: registered new interface driver usbhid

[    1.721532] usbhid: USB HID core driver

[    1.724973] NET: Registered protocol family 17

[    1.725167] Key type dns_resolver registered

[    1.726498] zswap: loading zswap

[    1.726592] zswap: using lz4 compressor

[    1.731113] Btrfs loaded

[    1.732585] Freeing unused kernel memory: 128K (c0631000 - c0651000)

[    1.776018] mmc0: new high speed SDHC card at address e624

[    1.783853] mmcblk0: mmc0:e624 SU08G 7.40 GiB

[    1.790181]  mmcblk0: p1 p2 p3

[    1.887089] Indeed it is in host mode hprt0 = 00021501

[    2.033096] udevd[57]: starting version 175

[    2.103907] usb 1-1: new high-speed USB device number 2 using dwc_otg

[    2.104096] Indeed it is in host mode hprt0 = 00001101

[    2.614084] random: nonblocking pool is initialized

[    2.942257] usb 1-1: New USB device found, idVendor=0424, idProduct=9514

[    2.942293] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0

[    2.943459] hub 1-1:1.0: USB hub found

[    2.943672] hub 1-1:1.0: 5 ports detected

[    3.225009] usb 1-1.1: new high-speed USB device number 3 using dwc_otg

[    3.309292] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00

[    3.309325] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0

[    3.312527] smsc95xx v1.0.4

[    3.371158] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:94:07:ca

[    3.451035] usb 1-1.2: new low-speed USB device number 4 using dwc_otg

[    3.555938] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c315

[    3.555973] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0

[    3.555989] usb 1-1.2: Product: Logitech USB Keyboard

[    3.556005] usb 1-1.2: Manufacturer: Logitech

[    3.571836] input: Logitech Logitech USB Keyboard as /devices/platform/bcm2708_usb/usb1/1-1/1-1.2/1-1.2:1.0/0003:046D:C315.0001/input/input0

[    3.576466] hid-generic 0003:046D:C315.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-bcm2708_usb-1.2/input0

[    3.650033] usb 1-1.5: new high-speed USB device number 5 using dwc_otg

[    3.734698] usb 1-1.5: New USB device found, idVendor=0bda, idProduct=8179

[    3.734733] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3

[    3.734800] usb 1-1.5: Product: 802.11n NIC

[    3.734825] usb 1-1.5: Manufacturer: Realtek

[    3.734840] usb 1-1.5: SerialNumber: 00E04C0001

[    5.686510] BTRFS: device label xbian devid 1 transid 152 /dev/mmcblk0p2

[    6.336471] BTRFS info (device mmcblk0p2): enabling auto defrag

[    6.336535] BTRFS info (device mmcblk0p2): disk space caching is enabled

[    6.336550] BTRFS: has skinny extents

[    6.401201] BTRFS: detected SSD devices, enabling SSD mode

[   10.213681] BTRFS info (device mmcblk0p2): disk space caching is enabled

[   13.777219] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup

[   14.845019] vchiq: vchiq_init_state: slot_zero = 0xd6000000, is_master = 0

[   14.866624] bcm2835-cpufreq: switching to governor powersave

[   14.866666] bcm2835-cpufreq: switching to governor powersave

[   14.873519] bcm2835-cpufreq: switching to governor performance

[   14.873558] bcm2835-cpufreq: switching to governor performance

[   16.650687] udevd[838]: starting version 175

[   16.859539] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup

[   20.604740] r8188eu: module is from the staging directory, the quality is unknown, you have been warned.

[   21.054074] Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_D_CUT_1T1R_RomVer(0)

[   21.632814] usbcore: registered new interface driver r8188eu

[   22.478967] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.

[   23.474982] init: failsafe main process (345) killed by TERM signal

[   26.229013] r8188eu 1-1.5:1.0: Direct firmware load failed with error -2

[   26.229043] r8188eu 1-1.5:1.0: Falling back to user helper

[   27.503298] r8188eu 1-1.5:1.0: Direct firmware load failed with error -2

[   27.503328] r8188eu 1-1.5:1.0: Falling back to user helper

[   59.925516] init: wait-for-state (xbmcxbmc-loaded) main process (1357) killed by TERM signal

[   61.028236] init: xbian-failaccess main process (459) killed by TERM signal

[   67.295678] init: xbmc-failed-start main process (665) killed by TERM signal

[   67.456354] init: wait-for-state (zram-swapxbmc-done) main process (1261) killed by TERM signal

[   68.982724] Adding 250876k swap on /dev/mmcblk0p3.  Priority:0 extents:1 across:250876k SSFS

[   83.954468] init: xbmc main process (1348) terminated with status 132

[   86.114243] init: wait-for-state (kill-splashxbmc-exits) main process (1930) killed by TERM signal

[   98.018503] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).

[  193.898813] usb 1-1.5: USB disconnect, device number 5

[  212.509892] usb 1-1.5: new high-speed USB device number 6 using dwc_otg

[  212.594416] usb 1-1.5: New USB device found, idVendor=0bda, idProduct=8179

[  212.594440] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3

[  212.594455] usb 1-1.5: Product: 802.11n NIC

[  212.594466] usb 1-1.5: Manufacturer: Realtek

[  212.594478] usb 1-1.5: SerialNumber: 00E04C0001

[  212.600067] Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_D_CUT_1T1R_RomVer(0)

[  212.962225] r8188eu 1-1.5:1.0: Direct firmware load failed with error -2

[  212.962255] r8188eu 1-1.5:1.0: Falling back to user helper

[  213.321030] r8188eu 1-1.5:1.0: Direct firmware load failed with error -2

[  213.321059] r8188eu 1-1.5:1.0: Falling back to user helper

[  617.404382] init: tty1 main process ended, respawning

[  617.414519] init: tty2 main process (1916) killed by TERM signal

[  810.056114] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup

[  811.546434] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1

[  849.336737] r8188eu 1-1.5:1.0: Direct firmware load failed with error -2

[  849.336805] r8188eu 1-1.5:1.0: Falling back to user helper

[  859.213426] r8188eu 1-1.5:1.0: Direct firmware load failed with error -2

[  859.213456] r8188eu 1-1.5:1.0: Falling back to user helper

[  871.448641] r8188eu 1-1.5:1.0: Direct firmware load failed with error -2

[  871.448674] r8188eu 1-1.5:1.0: Falling back to user helper

[  893.282858] r8188eu 1-1.5:1.0: Direct firmware load failed with error -2

[  893.282889] r8188eu 1-1.5:1.0: Falling back to user helper

I hope it can help you guys Smile

Thanks again for your help !

Cleaning up formatting.

Okay, so your wifi stick (TP-Link TL-WN725N) is recognized and it seems that the correct driver is loaded too.
Hmmm... or maybe it isn't the correct one!? You should have 8188eu, but you do have r8188eu loaded....
But I'm not really sure if the "r" one isn't equivalent...

Nevertheless it's certain that there is a problem with this driver version and your stick / firmware:

Code:

r8188eu 1-1.5:1.0: Direct firmware load failed with error -2

Do I understand right, that your wifi stick isn't listed anymore in xbian-config's network settings at all?
Maybe you could also post:

Terminal

sudo iwconfig

As I said, I'm not an expert - just trying to post what I would do in your situation.
And I'm thinking I would try also to compile the 8188eu driver by myself.
There's is a thread about your wifi stick and compiling the driver on the official RPi forum: http://www.raspberrypi.org/forums/viewtopic.php?t=62371&p=618445

PS: You can put your long outputs into [ code ] blocks instead of [ term ] ones.

Ok here is the output for the iwconfig :

Code:

wlan0     unassociated  Nickname:"<WIFI@REALTEK>"

          Mode:Auto  Frequency=2.412 GHz  Access Point: Not-Associated

          Sensitivity:0/0

          Retry:off   RTS thr:off   Fragment thr:off

          Encryption key:off

          Power Management:off

          Link Quality:0  Signal level:0  Noise level:0

          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0

          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

dummy0    no wireless extensions.

lo        no wireless extensions.

eth0      no wireless extensions.

i'm gonna check this thread, thanks.

Ok, so check the post from raspierre2. He linked and posted a how-to.

This should be fixed by whomever is currently maintaining the Xbian kernel package. Likely mk01

I have an error when I want to install git :

Terminal

Failed to fetch http://mirrordirector.raspbian.org/raspbian/pool/main/g/git/git-man_1.7.10.4-1+wheezy1+rpi2_all.deb Hash Sum mismatch
Failed to fetch http://mirrordirector.raspbian.org/raspbian/pool/main/g/git/git_1.7.10.4-1+wheezy1+rpi2_armhf.deb Hash Sum mismatch
E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing?

And without git, I can't clone the repository

PS : apt-get update makes an error too :
W: Failed to fetch xz:/var/lib/apt/lists/partial/mirrordirector.raspbian.org_raspbian_dists_wheezy_main_binary-armhf_Packages Hash Sum mismatch

E: Some index files failed to download. They have been ignored, or old ones used instead.

Can you check if the firmware-realtek package is installed:

Code:

apt-get install firmware-realtek

I think it's installed :

Code:

Reading package lists... Done

Building dependency tree

Reading state information... Done

firmware-realtek is already the newest version.

0 upgraded, 0 newly installed, 0 to remove and 3 not upgraded.

Maybe the problem comes from the apt-get upgrade problem no ?

(27th Sep, 2014 09:31 PM)Thib Wrote: [ -> ]I have an error when I want to install git :

Terminal
Failed to fetch http://mirrordirector.raspbian.org/raspbian/pool/main/g/git/git-man_1.7.10.4-1+wheezy1+rpi2_all.deb Hash Sum mismatch
Failed to fetch http://mirrordirector.raspbian.org/raspbian/pool/main/g/git/git_1.7.10.4-1+wheezy1+rpi2_armhf.deb Hash Sum mismatch
E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing?

[...]

Looks like your RPi isn't connected to the internet. Big Grin

So please check your network cable and router to ensure that eth0 gets a proper internet connection.

To check if you are really online, you could do a simple ping:

Terminal

ping -c 1 xbian.org

Ok :o It was only connected locally to my PC. That's weird.
I'm trying the tuto but I don't understand everything.
Anyway to delete the actual driver and download a new one ?

As it seems that you did hit me on my social day, I've tried to compile it on kernel 3.15.8+ for you.
But sorry, I wasn't successful. Compiling itself was working, but I can't load the driver:

Terminal

xbian@xbian ~ $ sudo modprobe 8188eu
ERROR: could not insert '8188eu': Exec format error

Maybe you have to wait for one of the Xbian masters ....

Pages: 1 2

Thib

CurlyMo

Thib

josch

Thib

josch

Thib

josch

f1vefour

Thib

CurlyMo

Thib

josch

Thib

josch