Setup Static IP via Config

[DLD]

When using XBian Config I can't set up a Static IP, just looking for a little help on what values I should be using. The error I get is after entering these values, I scan and find my Wifi, enter my password (correctly) it restarts my wlan0 and then tires to connect and i get the error 'Failed to connect to WIFI_NAME'.

• I have version XBian 1.0Beta2
• I've been trying with both ethernet and USB dongle is plugged in
• The USB dongle is the only USB device plugged in and it's this device (http://www.jbhifi.com.au/computers/networking/d-link/wireless-n-nano-usb-adapter-sku-50637)
• Within the config (COnfig > Settings > Network) the options I see are:
  IP Address*:
  Netmask*:
  Gateway*:
  Nameserver*:
  Nameserver*:
  
  I've been trying various versions of:
  IP Address*: 192.168.1.168
  Netmask*:255.255.255.0
  Gateway*:192.168.1.1 OR 127.0.0.1
  Nameserver*:192.168.1.1 OR [blank] OR [my ISP DNS IP Primary]
  Nameserver*: [blank] OR [my ISP DNS IP Primary]
• I can't set the static IP via my Router (cheap Netcomm)
• The output of ifconfig and netstat -nr are below if that helps, I've tweaked some of the details as I wasn't sure if they were sensitive.
  

Any ideas what I should be settings these values too?

Terminal

Last login: Sat Dec 14 22:20:27 on ttys001
DLDs-MacBook-Pro-3:~ DLD$ ifconfig
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
options=3<RXCSUM,TXCSUM>
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=2b<RXCSUM,TXCSUM,VLAN_HWTAGGING,TSO4>
ether c7:2a:13:263:a2
media: autoselect (none)
status: inactive
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether e3:ce:8e:02:e1:5c
inet6 fe80::e6ce:8fff:fe02:e25a%en1 prefixlen 64 scopeid 0x5
inet 192.168.1.168 netmask 0xffffff00 broadcast 192.168.1.255
media: autoselect
status: active
fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078
lladdr c4:2c:14:ee:ff:83:07:e5
media: autoselect <full-duplex>
status: inactive
p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304
ether 05:cc:8e:02:ee:5b
media: autoselect
status: inactive

Terminal

DLDs-MacBook-Pro-3:~ DLD$ netstat -nr
Routing tables

Internet:
Destination Gateway Flags Refs Use Netif Expire
default 192.168.1.1 UGSc 19 3 en1
127 127.0.0.1 UCS 0 0 lo0
127.0.0.1 127.0.0.1 UH 6 21954 lo0
169.254 link#5 UCS 0 0 en1
192.168.1 link#5 UCS 3 0 en1
192.168.1.1 0:60:64:41:2e:94 UHLWIir 20 2670 en1 1024
192.168.1.2 b8:27:eb1:5:c8 UHLWIi 0 7846 en1 1000
192.168.1.168 127.0.0.1 UHS 0 3 lo0
192.168.1.255 ff:ff:ff:ff:ff:ff UHLWbI 0 10 en1

Internet6:
Destination Gateway Flags Netif Expire
::1 link#1 UHL lo0
fe80::%lo0/64 fe80::1%lo0 UcI lo0
fe80::1%lo0 link#1 UHLI lo0
fe80::%en1/64 link#5 UCI en1
fe80::e6cc:8eff:fe03:e25b%en1 e3:ce:8d:2:e1:3a UHLI lo0
ff01::%lo0/32 fe80::1%lo0 UmCI lo0
ff01::%en1/32 link#5 UmCI en1
ff02::%lo0/32 fe80::1%lo0 UmCI lo0
ff02::%en1/32 link#5 UmCI en1