[SOLVED] lirc X10 stopped working after apt-get upgrade

[-AB-]

Hi all,

I have a Raspberry Pi 2B with an X10 remote. Everything fine so far, until last week I decided to change a running system, and apt-get updated and upgraded.

After reboot, remote not working.
mode2 --raw still responds to key presses, lirc deamon starts without complaints, but irw does not output anything, it doesn't even get to that, as it closes instantly without *any* output.

Terminal

xbian@mumepc ~ $ irw
xbian@mumepc ~ $

The only thing I found and thought might be a problem was the following lines in dmesg:

Code:

[    9.741303] bcm2708_rng_init=afbfe000
[   10.152178] random: nonblocking pool is initialized
[   10.167971] lirc_dev: IR Remote Control driver registered, major 244
[   10.304103] lirc_rpi: module is from the staging directory, the quality is unknown, you have been warned.
[   10.352095] bcm2708_i2c 3f804000.i2c: BSC1 Controller at 0x3f804000 (irq 79) (baudrate 100000)
[   10.475211] snd-hifiberry-digi sound: ASoC: CPU DAI (null) not registered
[   10.475260] snd-hifiberry-digi sound: snd_soc_register_card() failed: -517
[   10.508605] pinctrl-bcm2835 3f200000.gpio: pin gpio18 already requested by lirc_rpi; cannot claim for 3f203000.i2s
[   10.508633] pinctrl-bcm2835 3f200000.gpio: pin-18 (3f203000.i2s) status -22
[   10.508648] pinctrl-bcm2835 3f200000.gpio: could not request pin 18 (gpio18) from group gpio18  on device pinctrl-bcm2835
[   10.508659] bcm2708-i2s 3f203000.i2s: Error applying setting, reverse things back
[   10.509395] snd-hifiberry-digi sound: ASoC: CODEC DAI wm8804-spdif not registered
[   10.509484] snd-hifiberry-digi sound: snd_soc_register_card() failed: -517
[   10.565885] smsc95xx v1.0.4
[   10.656249] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:fc:49:ad
[   10.657275] usbcore: registered new interface driver smsc95xx
[   10.657469] snd-hifiberry-digi sound: ASoC: CODEC DAI wm8804-spdif not registered
[   10.657489] snd-hifiberry-digi sound: snd_soc_register_card() failed: -517
[   11.023585] wm8804 1-003b: revision E
[   11.029799] snd-hifiberry-digi sound: wm8804-spdif <-> 3f203000.i2s mapping ok
[   11.262449] lirc_rpi: auto-detected active high receiver on GPIO pin 18
[   11.262803] lirc_rpi lirc_rpi: lirc_dev: driver lirc_rpi registered at minor = 0
[   11.262818] lirc_rpi: driver registered!

bcm2708 and lirc_rpi seem to fight over a GPIO pin (however, lirc seems to win?)

Can I discourage lirc from using the GPIO pins? The X10 uses a USB connector anyway:

Code:

[    4.312574] usb 1-1.3: new low-speed USB device number 4 using dwc_otg
[    4.429815] usb 1-1.3: New USB device found, idVendor=0bc7, idProduct=0006
[    4.429874] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.429898] usb 1-1.3: Product: USB Receiver
[    4.429922] usb 1-1.3: Manufacturer: X10 Wireless Technology Inc

Any more information I can provide? Really don't know how to proceed here

Thanks in advance