[CurlyMo]

Updating to kernel 3.10.51 works fine when using the method i posted in my pull request.
Serial also works fine.

Syntax for a serial login prompt is in /etc/init/tty2.conf

Code:

# tty2 - getty
#
# This service maintains a getty on tty2 from the point the system is
# started until it is shut down again.

start on runlevel [23] and (
            not-container or
            container CONTAINER=lxc or
            container CONTAINER=lxc-libvirt)

stop on runlevel [!23]

respawn
exec /sbin/getty -L 115200 ttymxc0 vt102

However, it's not autostarting yet. Any hints here?

Open issues
- GPIO not working at all
- The HB takes quit a while to get from the hdmi_audio to the keymap stage:

Code:

[   18.770811] init: network-interface (can0) pre-start process (1482) terminated with status 2
[   19.455518] fsl-hdmi-dai hdmi_audio.14: ASoC: can't open interface hdmi_audio.14: -1
[   19.464923] fsl-hdmi-dai hdmi_audio.14: ASoC: can't open interface hdmi_audio.14: -1
[   19.818778] fsl-hdmi-dai hdmi_audio.14: ASoC: can't open interface hdmi_audio.14: -1
[ ok ] Setting preliminary keymap...done.

- Sometimes the root partition can't be found. A reboot will help most of the time:

Code:

Root partition /dev/mmcblk0p2 missing

- xbian-copy still fails
- An apt-get upgrade fails on the 06btrfs findmnt issue. Editing the file helps but it's not very friendly for regular users.

---

I managed to create a bootable HB image using the xbian-copy code adapted a little so it uses rsync instead of send/receive. Retried the xbian-copy with that new image but it still fails:

Code:

lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk
       x Preparing devices                                        x
       xqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqmount: block device /dev/mapper/loop0p1 is write-protected, mounting read-only
       x                                                          x mount: you must specify the filesystem type                               x
       mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj

Code:

umount: /tmp/btrfs-dest: not mounted
umount: /tmp/btrfs-source: not found
rmdir: failed to remove ‘/tmp/btrfs-source’: No such file or directory

Code:

[  338.905295] loop: module loaded
[  393.489929] device-mapper: uevent: version 1.0.3
[  393.494456] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised:  dm-devel@redhat.com
[  393.498916] bio: create slab <bio-2> at 2
[  394.076062] EXT4-fs (loop1): VFS: Can't find ext4 filesystem
[  394.076339] EXT4-fs (loop1): VFS: Can't find ext4 filesystem
[  394.076597] EXT4-fs (loop1): VFS: Can't find ext4 filesystem
[  394.076898] FAT-fs (loop1): bogus number of reserved sectors
[  394.076908] FAT-fs (loop1): Can't find a valid FAT filesystem
[  394.077172] FAT-fs (loop1): bogus number of reserved sectors
[  394.077181] FAT-fs (loop1): Can't find a valid FAT filesystem
[  394.080526] EXT4-fs (loop2): VFS: Can't find ext4 filesystem
[  394.080799] EXT4-fs (loop2): VFS: Can't find ext4 filesystem
[  394.080972] EXT4-fs (loop2): VFS: Can't find ext4 filesystem
[  394.081255] FAT-fs (loop2): bogus number of reserved sectors
[  394.081265] FAT-fs (loop2): Can't find a valid FAT filesystem
[  394.081436] FAT-fs (loop2): bogus number of reserved sectors
[  394.081444] FAT-fs (loop2): Can't find a valid FAT filesystem
[  394.086057] ISOFS: Unable to identify CD-ROM format.
[  394.087137] UDF-fs: warning (device loop2): udf_load_vrs: No anchor found
[  394.087149] UDF-fs: Rescanning with blocksize 2048
[  394.087307] UDF-fs: warning (device loop2): udf_load_vrs: No anchor found
[  394.087320] UDF-fs: warning (device loop2): udf_fill_super: No partition  found (1)
[  394.087831] F2FS-fs (loop2): Magic Mismatch, valid(0xf2f52010) - read(0x0 )
[  394.087842] F2FS-fs (loop2): Can't find a valid F2FS filesystem in 1th su perblock
[  394.087891] F2FS-fs (loop2): Magic Mismatch, valid(0xf2f52010) - read(0x0 )
[  394.087900] F2FS-fs (loop2): Can't find a valid F2FS filesystem in 2th su perblock

Looping through the xbian-copy steps manually still gives me this error:

Code:

[  830.735991] btrfs: ERROR did not find backref in send_root. inode=645, offset=0, disk_byte=220712960 found extent=220712960