[solved] pilight( to send) and lirc (to receive)
|
2nd Feb, 2014, 05:59 AM
Post: #1
|
|||
|
|||
[solved] pilight( to send) and lirc (to receive)
Hello all,
first of all you can be shure I googled and searched all ressources I could find and also had a lot of support from the pilight forum and curlymo already but unfortunately I still run into problems. The story in short: I try to make my RasPi able to receive IR-Signals and on these should switch radio controlled plugs with pilight activated by these IR-Signals. First attempts on Raspbian failed and I was advised by curlymo to use XBIAN because there was an lirc_rp1 module to use. I intalled XBIAN and started with getting lirc to run and it worked as a charme ... received and identified my signals as needed. Now, to get pilight running I installed it and switched it to module-mode by entering to settings.json "hw-mode": "module", "hw-socket": "/dev/lirc1" and enabled lirc_rp1 in etc/modules Now the RasPi freezes at start. On ssh with putty I can enter the user and after entering password the putty session also freezes. When connecting to my TV I see this: XBian GNU/Linux 7 xbian tty1 xbian login: [ 22.173770] Unable to handle kernel request at virtual address bf00b0e8 [ 22.173936] pgd = d620c000 [ 22.173998] [bf00b0e8] *pgd=16e44811, *pte=00000000, *ppte=00000000 [ 22.174144] Internal error: 0ops: 7 [#1] ARM [ 22.174225] Modules linked in: uinput zram frandomlirc_rpi lirc_dev [ 22.174416] CPU: 0 PID: 912 Comm: pilight-daemon Tainted: G C 3.10.12 #61 .... and have no control via Keyboard. (there's many more to follow, but because I have no way to copy I had to write it down by hand) I could reach the machine by "WinSCP" and changed the settings.json back. After that the RasPi boots as usual. Just to make sure all hardware is working I checked both either way and the IR-Receiver as single with lirc is working and the other way round when disablng lirc and running pilight as single my radio-controlled plugs react as they should. Could please anyone bring me into the right direction to make my plan work? Thank you in advance. Haggi |
|||
2nd Feb, 2014, 08:51 AM
Post: #2
|
|||
|
|||
RE: pilight( to send) and lirc (to receive)
Conclusion, somehow the lirc_rp1 kernel module is broken.
pilight - modular domotica solution
|
|||
2nd Feb, 2014, 09:16 AM
Post: #3
|
|||
|
|||
RE: pilight( to send) and lirc (to receive) | |||
2nd Feb, 2014, 07:38 PM
Post: #4
|
|||
|
|||
Re: pilight( to send) and lirc (to receive)
Wait for mk01 to react.
pilight - modular domotica solution
|
|||
2nd Feb, 2014, 08:39 PM
Post: #5
|
|||
|
|||
RE: pilight( to send) and lirc (to receive)
Hi!
It seems pilight wasn't the right choice for my problem so I got up early this sunday morning and started from scratch. I finally found a solution which is called rcswitch-pi. So I went back to wheezy and everything is running now. As this is not related to xbian anymore I think it is not adequate to post my how-to here. So ... thank you for your support and good bye! |
|||
3rd Feb, 2014, 12:52 AM
Post: #6
|
|||
|
|||
RE: [solved] pilight( to send) and lirc (to receive)
You could also have used the lirc_rpi module for lirc and the gpio hardware mode for pilight.
pilight - modular domotica solution
|
|||
« Next Oldest | Next Newest »
|