Threaded Mode | Linear Mode

turbo · 5th May, 2013, 05:16 PM

when i start up the rsp with xbian 1.0 Alpha 5 it stops (hang) on the initial setup.

what to do?

**rikardo1979** · 5th May, 2013, 05:23 PM

what method did you use to install it? also read my signature an follow the instructions for posting.
-thx-

turbo · 5th May, 2013, 05:30 PM

(5th May, 2013 05:23 PM)rikardo1979 Wrote: what method did you use to install it? also read my signature an follow the instructions for posting.
-thx-

I installed it on sd card with win 32 manager.

**rikardo1979** · 5th May, 2013, 05:53 PM

(5th May, 2013 05:30 PM)turbo Wrote:
(5th May, 2013 05:23 PM)rikardo1979 Wrote: what method did you use to install it? also read my signature an follow the instructions for posting.
-thx-

I installed it on sd card with win 32 manager.

thats nice, so what about the rest of informations? Did you read the how-to post?
witch such a post you hardly get any help as not enough infos to troubleshoot is provided.
sorry pal

turbo · 5th May, 2013, 06:09 PM

I downloaded the .img from http://xbian.org/download/

Installed it on a Transcend 8 GB SD card with win 32 imager

Inserted the SD card in the rsp and it starts up.

Then it stop when the screen with xbian initial setup and the loadingbar dont move.

So what to do?

**rikardo1979** · 5th May, 2013, 07:19 PM

- what is the power rating of your PSU?
- do you have any device plugged into RPi's USB ports directly?

jlabeeuw · 6th May, 2013, 04:52 AM

I have exactly the same problem here.

Power supply: 5V 1A
Raspi attachments: hdmi, network
4GB SD card
Pi Model B Revision 2.0 (512 MB)

I tried Alpha 5 both with the installer and win32 imager.
The screen shows that the initial setup is started, bar goes to 100% and then nothing anymore.
I notice that my DHPC server does not provide an IP. (tried again with wheezy, and got an IP, so no Hardware issue).

After this I tried the Alpha 4. (both with installer and imager), here, I even don't see anything (raspberry is not starting up).

Koenkk · 6th May, 2013, 04:58 AM

Plug the sdcard into your pc, on the partition that appears open the file "config.txt" and change

core_freq=375 to core_freq=250

If that doesn't help also change the

arm_freq=840 to arm_freq=700

jlabeeuw · 6th May, 2013, 05:22 AM

Thank you! setting core_freq to 250 worked for me.

t.becicka · 31st May, 2013, 04:41 AM

I have the same problem. System was already running but now stop at the very same point. Config.txt don't work for me. Can you help me please?

Koenkk · 31st May, 2013, 08:12 AM

Could you try a different SD card?

t.becicka · 31st May, 2013, 06:37 PM

I reinstall completely on the same SD and it works now, but I don't know why it stoped working before.

zilexa · 4th Jun, 2013, 01:40 AM

I would recommend using USBIT instead of Win32 imager next time. Not sure if it would make a difference but I had some corruption issues with old SD cards using win32imager. Never had an issue with USBIT: http://www.alexpage.de/usb-image-tool/

ChuckyDevil · 6th Jun, 2013, 04:34 AM

I had the same problem with an SD class 4. Class 10 works just fine.

**rikardo1979** · 6th Jun, 2013, 05:31 AM

(6th Jun, 2013 04:34 AM)ChuckyDevil Wrote: I had the same problem with an SD class 4. Class 10 works just fine.

Class 4 cards dont have a real use in RPi as they are way to slow.
Also look on our Wiki for recommended HW/SD cards which are tested and confirmed as good with RPi/XBian